12V 7000BTU Air Conditiaoner Evaporator Hanging Kit for Car Caravan Cooling USA

Description

Specification:
◆
Material:
Stainless Steel, ABS
◆
Voltage:
12V
◆
Rated power:
400-500W
◆
Rated current:
10-30A
◆
Undervoltage recovery: 14.5V
◆
Undervoltage protection: 10.5V
◆
Control method: manual adjustment
◆
Drive mode: standalone
◆
Cooling capacity:
5
00-2800W
◆
Evaporative fan air volume: 4A1200m3 / h
◆
Inner tube air volume: 4.5A2600m3 / h
◆
Working refrigerant: 600 + 20g R134a (except refrigerant)
◆
Thermal performance of the entire system:
7000 BTU / H
◆
Machine internal dimensions: 430 * 140 * 270mm
◆
Machine exterior dimensions: 460 * 280 * 360mm
◆
Internal weight: 5KG
◆
External weight: 16.6KG
Description:
1. The product 2800w cooling capacity is equivalent to 1.2 horses for household air conditioners. When the temperature of the cab is 29.5 degrees, the temperature of the air outlet is about 3-15 degrees.
2. The air conditioner is a horizontal split model. The outer unit is installed in the proper position outside the cab, and the wall mount machine is installed in a satisfactory position in the cab.
3. The air conditioner has a low-voltage protection cut-off function. If the battery's power is lower than the vehicle's starting voltage, it will automatically stop, and it will not affect the car's start, and it will not lose power. Air conditioning can be used normally after 3-5 minutes of starting the car again.
4. Suitable models: RV, electric car, engineering car, funicular, truck, excavator, etc.
Installation and use instructions:
1. The air conditioning system is installed in the same way as the home split air conditioning system. The customer can fix the main unit in the proper position outside the cab, install the wall-mounted tuyere in the satisfactory position of the cab, and connect the distribution expansion valve and pipe to the main unit. The length of the connecting pipe is as short as possible, and the compressor load is small. , power saving, better cooling effect.
2. Power connection. Connect the supplied wires to the wire connection of the air vent and the air conditioner main unit, and connect the wire nose on the air conditioner main unit to the battery. The principle of the length of the connecting line is as short as possible, the electric loss is small, the power is saved, and the continuous working time is longer.
3. Pump down. The vacuumed interface is connected to the pipe joint using a multi-function air conditioning refrigerant meter and a vacuum pump. The pumping is as thorough as possible until no gas is coming out.
4. Use R134a environmentally friendly refrigerant. Refrigerant filling also uses a multi-function filling table in the same way as all refrigerating air conditioning systems. The amount of filling is slightly different depending on the length of the pipeline. It can be used by adding 600g-700g of the company's supporting pipeline. Generally, it is determined by observing the flow state of the refrigerant in the liquid mirror on the combination meter. When there are not a lot of bubbles inside, it means that the refrigerant has been added enough.
5.The compressor has been filled with a sufficient amount of refrigerating machine oil, and the customer does not need to add additional oil. The model of the refrigerating machine oil is RL68H. The refrigerating machine oil has the characteristics of high insulation value and no water absorption, and is suitable for the electromechanical integration of new energy automobile air conditioner compressors. Never replace it with other grades of refrigerating machine oil or mix it with other grades of refrigerating machine oil.
Packing including：
1* Air conditioner
1* Evaporator
Accessory set
On Aug-30-21 at 22:35:09 PDT, seller added the following information: